Crushing Equipment
Gyratory Crusher
The gyratory crusher reduces run-of-mine ore to a transportable size suitable for secondary crushing or SAG milling. It serves large hard-rock mines where a jaw crusher would struggle with throughput or feed size.
Technical parameters
In the circuit, the machine sits directly under the primary surge bin. It accepts full truck loads without pre-screening. Its continuous crushing motion produces a coarser but uniform discharge, which then feeds screens or cone crushers.
The model table lists key dimensions and power ratings. Bottom diameter and feed port size define the machine's capacity envelope. As these increase, motor power, discharge opening range, and assembly weight scale accordingly. Selecting a model means matching the feed opening to the largest rock size in the blast and the power to the required throughput.
| Model | Bottom Diameter of Crushing Cone (inches) | Feed Port Size (inches) | Feed Port Size (mm) | Drive Shaft Speed (r/m) | Discharge Opening Width (mm) | Maximum Motor Power (kW) | Weight (t) | Weight of Moving Cone Assembly (t) |
|---|---|---|---|---|---|---|---|---|
| PXZ4265 | 65 | 42 | 1067 | 600 | 140-175 | 450 | 121 | 23 |
| PXZ5065 | 65 | 50 | 1270 | 600 | 150-175 | 450 | 154 | 30 |
| PXZ5475 | 75 | 54 | 1372 | 500 | 150-195 | 500 | 231 | 38 |
| PXZ6089 | 89 | 60 | 1524 | 500 | 165-220 | 710 | 362 | 67 |
| PXZ60110 | 110 | 60 | 1524 | 500 | 195-240 | 1000 | 560 | 116 |
| Discharge Opening Width (mm) | 140 | 150 | 165 | 175 | 195 | 210 | 220 | 240 | |
|---|---|---|---|---|---|---|---|---|---|
| Production Capacity (t/h) | PXZ4265 | 1508 | 1701 | 1981 | 2150 | ||||
| PXZ5065 | 1648 | 2152 | 2490 | ||||||
| PXZ5475 | 2510 | 2785 | 2970 | 3320 | |||||
| PXZ6089 | 3615 | 3881 | 4210 | 4826 | 5080 | ||||
| PXZ60110 | 5800 | 6210 | 6510 | 7000 |
| Model | Cavity Type | Feed Opening Size (mm) | Maximum Feed Size (mm) | Minimum Discharge Size (mm) | Maximum Discharge Size (mm) | Motor Power (kW) | Main Unit Dimensions (mm) | Main Unit Weight (kg) | ||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Stroke | Stroke | Stroke | Stroke | Stroke | Stroke | |||||||
| PYYZ100 | 16 | 22 | / | 16 | 22 | / | 75-90 | 2030×1840×2670 | 9500 | |||
| A | 320 | 250 | 35 | 35 | / | 100 | 95 | / | ||||
| B | 250 | 210 | 35 | 35 | / | 100 | 95 | / | ||||
| PYYZ200 | 18 | 25 | / | 18 | 25 | / | 160-200 | 2260×2090×2980 | 13400 | |||
| A | 340 | 280 | 35 | 35 | / | 105 | 100 | / | ||||
| B | 250 | 210 | 35 | 35 | / | 105 | 100 | / | ||||
| PYYZ300 | 25 | 32 | / | 25 | 32 | / | 220-250 | 2530×2350×3180 | 18200 | |||
| A | 380 | 320 | 35 | 35 | / | 100 | 95 | / | ||||
| B | 280 | 240 | 35 | 35 | / | 100 | 95 | / | ||||
| PYYZ500 | 18 | 25 | 32 | 18 | 25 | 32 | 280-315 | 3100×2780×3980 | 32700 | |||
| A | 500 | 420 | 50 | 55 | 60 | 105 | 100 | 95 | ||||
| B | 380 | 320 | 42 | 50 | 55 | 105 | 100 | 95 | ||||
| PYYZ800 | 32 | 40 | 50 | 32 | 40 | 50 | 500-630 | 3900×3535×5200 | 75000 | |||
| A | 560 | 470 | 65 | 70 | 75 | 105 | 100 | 95 | ||||
| PYY100 | 16 | 22 | / | 16 | 22 | / | 90 | 1950×1620×2140 | 5800 | |||
| A | 150 | 120 | 12 | 15 | / | 39 | 37 | / | ||||
| B | 130 | 105 | 10 | 11 | / | 33 | 31 | / | ||||
| C | 100 | 85 | 7 | 9 | / | 33 | 30 | / | ||||
| PYY200 | 25 | 32 | / | 25 | 32 | / | 200-220 | 2260×2090×2870 | 12700 | |||
| A | 225 | 180 | 22 | 26 | / | 45 | 40 | / | ||||
| B | 150 | 120 | 19 | 23 | / | 45 | 40 | / | ||||
| C | 80 | 60 | 12 | 14 | / | 40 | 35 | / | ||||
| PYY300 | 25 | 32 | / | 25 | 32 | / | 250-280 | 2530×2350×3190 | 16700 | |||
| A | 225 | 180 | 22 | 28 | / | 50 | 45 | / | ||||
| B | 150 | 125 | 19 | 23 | / | 45 | 40 | / | ||||
| C | 80 | 60 | 10 | 12 | / | 40 | 35 | / | ||||
| PYY500 | 34 | 42 | 50 | 34 | 42 | 50 | 315-355 | 3100×2780×3490 | 27000 | |||
| A | 280 | 220 | 24 | 26 | 30 | 45 | 35 | 30 | ||||
| B | 150 | 125 | 19 | 21 | 24 | 45 | 35 | 30 | ||||
| C | 100 | 80 | 12 | 12 | 14 | 35 | 30 | 25 | ||||
| PYY700 | 50 | 60 | 70 | 50 | 60 | 70 | 450-560 | 3650×3298×4122 | 50000 | |||
| A | 300 | 220 | 22 | 26 | 28 | 50 | 42 | 35 | ||||
| B | 180 | 125 | 17 | 20 | 25 | 50 | 42 | 35 | ||||
| C | 130 | 80 | 10 | 12 | 14 | 46 | 39 | 34 | ||||
| PYY800 | 58 | 70 | 80 | 58 | 70 | 80 | 630 | 3900×3535×4563 | 63000 | |||
| A | 320 | 220 | 22 | 26 | 30 | 50 | 42 | 36 | ||||
| B | 180 | 125 | 19 | 21 | 24 | 50 | 42 | 36 |
| Model | Stroke (mm) | 8 | 12 | 16 | 20 | 25 | 30 | 35 | 40 | 45 | 50 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PYY100 | 16 | 35-40 | 45-55 | 55-65 | 65-75 | 75-85 | 90-100 | 105-115 | / | / | / |
| 22 | 45-50 | 55-65 | 65-75 | 75-90 | 85-105 | 100-125 | 115-135 | / | / | / | |
| PYY200 | 25 | 85-105 | 105-130 | 130-155 | 150-180 | 185-220 | 220-255 | 255-280 | 270-310 | 285-330 | / |
| 32 | / | 130-160 | 155-175 | 175-200 | 190-230 | 230-260 | 260-310 | 280-320 | 290-350 | / | |
| PYY300 | 25 | 115-140 | 135-165 | 165-190 | 172-210 | 200-235 | 235-270 | 270-310 | 290-340 | 320-360 | / |
| 32 | 130-160 | 155-200 | 210-250 | 225-255 | 245-295 | 280-330 | 320-365 | 340-385 | 365-405 | / | |
| PYY500 | 34 | / | 245-270 | 270-305 | 310-340 | 330-380 | 385-435 | 445-495 | 495-530 | 540-585 | 575-640 |
| 42 | / | 280-320 | 320-355 | 350-395 | 390-460 | 475-525 | 550-605 | 610-665 | 650-715 | / | |
| 50 | / | 330-365 | 370-410 | 410-455 | 465-535 | 540-595 | 590-655 | 650-715 | / | / | |
| PYY700 | 50 | / | 300-370 | 375-440 | 445-520 | 525-590 | 590-690 | 675-755 | 740-840 | 830-920 | 880-980 |
| 60 | / | 360-430 | 430-495 | 490-555 | 550-640 | 630-730 | 730-835 | 800-905 | 900-990 | 950-1040 | |
| 70 | 420-500 | 495-570 | 565-640 | 645-725 | 700-790 | 770-865 | 880-1000 | 980-1070 | / | ||
| PYY800 | 58 | 400-480 | 470-540 | 535-610 | 595-670 | 660-760 | 760-845 | 835-945 | 935-1020 | 1000-1100 | |
| 70 | 460-540 | 535-610 | 600-670 | 660-760 | 750-850 | 860-935 | 930-1050 | 1040-1130 | / | ||
| 80 | 520-600 | 590-670 | 650-750 | 745-855 | 850-950 | 940-1030 | 1030-1130 | 1120-1250 | / |
Standard-model catalogue figures. Actual capacity, power draw and wear life shift with ore properties, feed gradation and circuit conditions. Use them to shortlist, then confirm the duty by testwork, flowsheet calculation and a written confirmation from the manufacturer.
What decides the selection
Before specifying a model, confirm the characteristics of the orebody: unconfined compressive strength, abrasion index, moisture content, and the top size expected from the mine. The required throughput and desired product P80 must be defined. A site review of the dump pocket and downstream circuit layout is essential to verify clearance for the crusher and its discharge.
- Maximum run-of-mine feed size
- Ore hardness and abrasiveness
- Moisture and clay content
- Target closed-side setting
- Required throughput per hour
- Open-circuit or closed-circuit configuration
- Wear part life and maintenance access
Other crushing machines
- Jaw Crusher16 models
- Hammer Crusher20 models
- Impact Crusher9 models
- Roller Crusher12 models
- High-Pressure Grinding Roller (HPGR)13 models
- European Version Jaw Crusher6 models
ISO 9001 / ISO 14001 / ISO 45001 / ISO 9712 / CE / CSA W47.1 / CNAS accredited laboratory
Send the duty, get a sized proposal
Tell us the ore, the throughput and the target product. Our process engineers come back with a flowsheet position, a model shortlist and the testwork we would need to confirm it.